Reinforcement of the existing structure to meet increased demand with the addition of conveyors and process utilities. The existing facility consists of prefabricated steel frames and portal frames that have been analyzed for additional equipment loads and reinforced to support these loads. ... More Details
New 14,000 square foot addition to the existing facility. The structure consists of metal roof deck on wide flange steel beams and girders supported by wide flange columns and enclosed with insulated metal panel walls (IMP) fastened to steel wind girts spanning... More Details
New 36,000 square foot addition to the existing facility. The structure consists of metal roof deck on wide flange steel beams and girders supported by wide flange columns and enclosed with insulated metal panel walls (IMP) fastened to steel wind girts spanning... More Details
Replacement of a 320 square foot, steel framed platform supporting a water tank that has been a local landmark for over 100 years. The existing platform members were severely deteriorated which necessitated the replacement. New galvanized steel members were installed in between... More Details
New 11,000 square foot expansion to an existing facility consisting of a prefabricated metal building with standing seam metal roof fastened to roof purlins that span in between the rigid steel frames. The walls consist of 12” reinforced masonry transitioning to an... More Details
New 12,000 square foot single-story addition to the existing facility consisting of metal roof deck on open web steel roof joists and joist girders bearing on concrete masonry walls and wide flange steel columns. The perimeter of the addition is clad with... More Details
A deteriorating concrete floor slab within the cook room and adjacent storage area of the existing facility required the installation of a 4,300 square foot reinforced, 4 inch thick concrete overlay on top of the existing concrete floor. The existing floor finishes... More Details
The structure consists of metal roof deck on open web steel joists and joist girders bearing on steel columns and site cast tilt-up concrete panels with an industrial concrete slab-on-grade. The equipment foundation required very close coordination with the manufacturer and special... More Details
Replacement of approximately 185,000 square feet of concrete slab-on-grade inside an existing facility due to moisture related issues. The new slab-on-grade is poured on top of a gravel sub-base and vapor barrier. Replacement of the floor slab necessitated the erection of a... More Details
New 5,000 square foot, single-story addition to an existing vehicle maintenance facility. The structure consists of open web steel joists bearing on site-cast concrete tilt-up wall panels. The framing system was designed to support a 10-ton bridge crane and is completely founded... More Details
New 15,000 square foot, single-story maintenance facility. The structure consists of open web steel joists bearing on concrete masonry walls. The framing system was designed to support a 15-ton bridge crane and is completely founded on a shallow foundation system. More Details
Equipment foundations inside an existing structure to support aluminum extrusion presses, pullers and stretchers, and a 40 foot deep casting pit. Several of the equipment foundations measure more than four feet in thickness. More Details
New 170,000 square foot mix and distribution facility including offices, three-story mixing tower, attached rail shed, and installation of all process equipment. The structure consists of metal roof deck on open web steel joists supported on site-cast tilt-up concrete wall panels and... More Details
Five new industrial warehouse buildings ranging in size from 17,000 square feet to over 80,500 square feet. The structure of each individual building consists of pre-engineered metal frames and enclosed with either full height concrete masonry walls or site-cast tilt-up concrete wall... More Details
New 46,000 square foot addition to the existing facility consisting of a 6,300 square foot depalletizing area, a 7,800 square foot two-story associate service facility (ASF), and a 33,000 square foot, 75 foot tall racked supported G.E.S. The roof structure of the... More Details
New 250,000 square foot single-story addition to an existing facility consisting of 100,000 square feet of additional bakery and 150,000 square feet of high density, heavy automated distribution. The structure consists of metal roof deck on top of open web steel joists... More Details
New 140,000 square foot single-story addition including new warehouse, process, and packaging areas and free-standing rail shed. The structure consists of metal roof deck on open web steel joists and joist girders supported by site-cast insulated tilt-up concrete wall panels. The entire... More Details
The new Enkei Florida plant, which is Enkei’s third manufacturing facility in the U.S. and ninth worldwide, was scheduled in five phases on a 22-acre site. The first phase was a 30,000 square foot warehouse and the second phase was a 35,000... More Details
New 58,300 square foot warehouse addition to the existing facility consisting of metal roof deck on open web steel joists and joist girders supported on tube steel columns and site cast, tilt-up concrete wall panels. Since the roof height of the new... More Details
New steel framed elevated platform to support two refrigeration condensers with a combined weight of 66,000 pounds. The structure consists of wide flange steel beams bearing on tube steel columns and shallow foundations. All four sides of the structure contain tube steel... More Details
New 600,000 square foot process and distribution facility. Structure consists of a structural steel roof with open web joists and joist girders and floors supported on load bearing site-cast concrete tilt-up wall panels. The entire facility is founded on rammed drilled shafts. ... More Details